Electron Microscope Specimen Mounts and Holders
Electron Microscopy Sciences Critical Point Dryer 12 Specimen Holder
Machined from solid steel and brass/nickel plated. Incorporates a stainless steel mesh top and bottom to allow for fluid exchange. Comes with two sections; each section holds 6 specimens in 6 cavities cavity measures 7.5mm (D)x6mm(H)..
Ted Pella Inc Standard SEM Pin Stub Mount, Ø12.7mm x 8mm pin height, 1000/pack
FEI, Tescan, ZEISS (also for Philips, Aspex, LEO, Cambridge, AMRAY, Leica, CamScan, ETEC), aluminum, grooved edge
Electron Microscopy Sciences Applied Physics CeB6 Cathode for Leica Lithography MVM
Lanthanum hexaboride (LaB6) and cerium hexaboride (CeB6) cathodes are ideal for many small spot size applications such as SEM, TEM, surface analysis and metrology, and for high current applications such as microwave tubes, lithography, electron-beam welders, X-ray sources and free electron lasers. Greater brightness from low work function yielding higher currents at lower temps than tungsten. Cambridge MVM base.
Type: CEBIX (CeB6)
Angle: 90°
Tips: 20 mm
Type: non-shunted
Chemglass Life Sciences Plate Holder, 96-Well, for Stackable Incubator Shakers
Plate Holder, 96-Well, for Stackable Incubator Shakers
Grainger Machine Vise 2 Fixed
The Dayton Machine Vise has a 2 inch jaw face and a maximum jaw opening of 2 inches. It is made of ductile iron with a hardened steel vise screw and replaceable steel jaw plates. The vise has a flat base that allows it to be permanently mounted. The vise can handle up to 550 lbs of clamping force. This medium duty machine vise is suitable for precision workholding applications.
Electron Microscopy Sciences Standard Pin SEM Stub Mini, 6.6 x 1.3 mm Head, 9.5 mm Pin, Aluminum
Mini SEM pin stub mount for Cambridge, Leica, ZEISS/LEO, FEI/Philips, CamScan, Tescan, ETEC and Amray. Made from lathe finished ultra-pure aluminum.
Head: 6.6 x 1.3 mm
Pin height: 3/8"
Electron Microscopy Sciences SEM Mount Hitachi M4 1" Surface 9-Division, 1/4" height, Aluminum
Hitachi cylinder mount has a M4 tapered hole with female thread. Made from lathe finished ultra-pure aluminum. M4 tapered hole.
Head: 1"
Height: 6 mm
Electron Microscopy Sciences Hitachi M4 SEM Cylinder Mount 1-1/4" surface, 1/4" height, Aluminum
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 1-1/4"
Height: 1/4"
Electron Microscopy Sciences Hitachi M4 SEM Cylinder Mount 1-1/4" surface, 1/4" height, Aluminum
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 1-1/4"
Height: 1/4"
Electron Microscopy Sciences Hitachi M4 SEM Cylinder Mount 1" surface, 3/8" height, Aluminum
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 1"
Height: 3/8"
Electron Microscopy Sciences Hitachi M4 SEM Cylinder Mount 1" surface, 3/8" height, Aluminum
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 1"
Height: 3/8"
Electron Microscopy Sciences Hitachi M4 SEM Cylinder Mount 2" surface, 1/4" height, Aluminum
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 2"
Height: 1/4"
Electron Microscopy Sciences SEM Cylinder Mount 45° Angle 5/8" Surface, Aluminum
Scanning electron microscope specimen mount with 45 degree angle. Made from lathe finished ultra-pure aluminum.
Head: 5/8"
Height: 3/8"
Electron Microscopy Sciences Multi Holder 45 ° for 6 pin stubs, 3.2 mm x 8mm Pin
This 35 mm in diameter 45 Degree multi pin holder is designed to save time. It allows for a higher SE signal without having to tilt the specimen. It is made from machined aluminum with stainless steel Allen set screws. It accommodates up to six standard 12.7 mm (1/2") pin stubs.
Type: 3.2 mm x 8 mm Pin
Electron Microscopy Sciences Capsule Block Storage Box
For the storage of 15 capsule blocks in numbered cavities.